Hook Up Wood Stove To Furnace. Free Nsa Hookups!

Up Stove Hook To Furnace Wood

Add-On Wood Burning Furnance / Heating with Wood

Linking indoor woodstove furnace to existing gas furnace ductwork. |

The reason is that you could suck in the exhaust from the wood stove and circulate it throughout the house. This means you could be spreading carbon monoxide throughout the house, and endanger your family. Now, if you leave your furnace blower running continuously, then the warmed up air from the. 25 Jun Hey guys new to this forum. I'm getting ready to install a wood furnace in my basement. My wife wants to pay the pros but I'm a DIY guy on everything. I have my flue figured out but I'm concerned on how to force the duct from my new furnace thru the same duct work that my current gas furnace/ac unit run. INSTALLATION & OPERATION MANUAL. Manufactured By: England's Stove Works, Inc. PO Box Monroe, VA Rev. 1/ Wood Add-On Furnace . MODELS , SHW40, TRW SAVE THESE INSTRUCTIONS.

I am installing a new wood add-on stove in the basement and want to hook it in to my forced air furnace duct work to help move the air in the house.

attaching wood furnace to current duct? | Forums Home

I have heard it can be done, but I am confused as to how or where to hook up the hot air pipe. Some say to hook it into the cold air return, but what about CO 2 build up? Others say you can hook in to the output side and run it through the furnace, but I was told that could here the forced air furnace, and that I would have to put dampers in to by-pass the electric furnace altogether.

I will assume this wood stove has a proper air jacket from which heated air can be drawn?

Your Answer

The possibility of dangerous gases infiltrating into this jacket is a valid concern and entirely dependent on the integrity of the firebox. This can only be done by careful inspection and possibly some sort of pressure test. In theory, this can be just as safe as any other fuel burning furnace.

Hook Up Wood Stove To Furnace

The purpose of piping the stove's heated output air to the furnace return air is that the furnace is then fed pre-heated air. This minimizes the amount of energy the furnace must use to raise it to the proper distribution temperature. It doesn't make sense to apply the wood heated air to the furnace circulating air unless the furnace's output temperature was deliberately reduced, relying on the wood heat to make up the difference.

This would be very difficult to properly regulate since thermostatic control of a wood burning appliance is marginal at best unless you are burning wood pellets. Whether the pre-heated air from the wood stove is bad for the furnace would depend on just how hot this air is. This is highly variable depending on air flow, fuel wood type and loading, as well as combustion air or damper volume.

Hook Up Wood Stove To Furnace

With adequate air jacket flow and typical wood stove firing practice, I don't see this being a problem for the furnace. But there's a lot of variables. It would be easy to misfire the stove and reach damaging temperatures. Some sort of damper bypass system would be ideal, but the controls needed would be complicated to ensure adequate heat was delivered regardless of the stove's firing rate. Even then, Hook Up Wood Stove To Furnace will require careful monitoring. It'll always be possible to over fire the stove during low heat demand conditions, wasting fuel.

By hooking to the return of the furnace you are feeding hot air to the furnace; once it hits the temp limit switch the furnace fan will kick on and essentially you will have two blowers blowing the heat. This works very well to supply the entire home. If you connect it to the supply side and high temp hits the furnace fans limit switch, the two fans are going to fight each other. Most furnace fans have different speeds: My suggestion would be to hook up the wood stove to the return air and go to the gas furnace thermostat and turn the fan to the on position using your forced air furnace into a air handler: Remember the furnace is designed to grab cool or room temperature air and in the last step, heat it and dump it into the duct, so you should attempt to keep that air from getting too hot.

It should also Hook Up Wood Stove To Furnace the air by sucking additional air from throughout the house via the cold air returns. One thing to check would be to make sure the CFM rating of the furnace fan is larger than the CFM of the woodstove fan. By posting your answer, you agree to the privacy policy and terms of service.

Questions Tags Users Badges Unanswered. Join them; it only takes a minute: Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the top. Why would you hook up the heat output of a wood stove to the cold air return read article an electric forced-air furnace? So I am confused.

Can some one help? Some pictures of this stove would be helpful. Make, model so we can check out their website would help with giving advice.

The house was built in I don't know if that could help you pinpoint what duct work may be ran through the house. Putting people and solutions together since About the Author Dale Yalanovsky has been writing professionally since

From your post, for some reason, I get the image of someone hooking the stovepipe coming out of the firebox into the HVAC duct expecting it to heat the house, which it would, probably momentarily and quite spectacularly. Is this stove actually a wood furnace with separate air jacket that connects to ducting?

How To Install A Wood Stove part 1

While CO2 can be dangerous when it displaces oxygenated air, what you really should be concerned about with any fuel burning appliance is CO - carbon monoxide, an odorless, tasteless, invisible, highly toxic gas.

Sign up or log in Sign up using Google. Sign up using Facebook.

What room is righ above it? Pipes are dripping down into unit and causing water to leak out of unit on You are not allowed to have a return air in the same room as a wood stove. So I am confused.

Sign up using Email and Password. Post as a guest Name.